How To Knit A Beret With A Visor

Table of contents:

How To Knit A Beret With A Visor
How To Knit A Beret With A Visor

Video: How To Knit A Beret With A Visor

Video: How To Knit A Beret With A Visor
Video: How to Knit a Beret | Easy Knitting Tutorial 2024, March
Anonim

The beret belongs to the category of those hats that almost never go out of fashion. Felt, woolen, leather or knitted beret can be worn with an elegant coat and a sports jacket. You can also do it with a visor. This detail is not only able to add sophistication to even the most uncomplicated beret, but also protect the upper part of the face from wind and rain. You can knit such a headdress both with knitting needles and crochet.

How to knit a beret with a visor
How to knit a beret with a visor

It is necessary

  • - 150 g of yarn of medium thickness;
  • - hook on the thickness of the yarn;
  • - hook on the line.

Instructions

Step 1

A beret with a visor can be knitted without seams if you start to perform it from above. When knitting the upper part, it doesn't matter if you use a regular crochet hook or on a fishing line. Tie a chain of 5 stitches and close it in a circle. It is better to knit the bottom in a spiral, without tying air loops to the height of the row.

Step 2

From the second hand, start adding loops evenly. You should end up with an almost flat bottom. It is only slightly curved upward. Add loops by knitting 2 columns per column of the previous row. In the second row, additions will go to each column, in the next - after 2, and so on. The further from the center, the greater the distance between the additions. Do not forget to control the process and remember or write down how many columns there are more in each row.

Step 3

Tie a circle with a diameter of 25-27 cm in this way if you are using soft thick wool. The circle can be made larger. Run 4-5 rows without adding. Then start decreasing the loops in the same order as you increased them. Knit in this way until you have a hole equal to the diameter of your head.

Step 4

Make a rim by knitting 4-5 rows without adding or subtracting. It is better to knit these row not in a spiral, but in circles, making 2 air loops at the beginning of each row to a height. Locate the visor and mark the beginning and end with a different color of thread. Mark the middle and mark it too.

Step 5

Make a visor from two or four parts. If the threads are stiff and dense, the visor can be single-layer. For a beret made of soft threads, a two-layer one is preferable. You can make a plastic spacer between the top and bottom. Tie the first row from the middle to the edge without adding or subtracting. Turn the job over. Make 2 loops on the rise, then 1 column, but do not knit them to the end, but slide them onto the fishing line. Tie the rest of the posts in the usual way. The second row, which starts from the middle, knit without adding, but do not touch the loops on the line. In the third row, make the chain and post again and slide them onto the line. There should be 4 loops. Tie the fourth, fifth and sixth rows straight.

Step 6

In the seventh and ninth rows, remove the start air loop again and the first post on the line. Knit even rows straight. Depending on the width of the visor, you can make another cycle - the tenth; knit the eleventh and twelfth rows straight; and on the thirteenth and fifteenth, remove the initial loops again. Finish knitting half on the side line and knit all removed loops with half-columns or simple columns.

Step 7

Along the line between the visor and the band, knit a row of half-columns to the middle of the visor. Knit the second half in the same way as the first, observing symmetry. If the visor is single-layer, finish the last row on the side line and knit all the removed posts and chains of air loops with half-columns. The last loop should be on the line between the visor and the band.

Step 8

To complete the bottom half, knit a row of half-stitches again to the middle. Knit it also in two parts, like the upper one. After finishing the last quarter, join the top and bottom with a row of half-columns, leaving the seam open. Insert the spacer and cover the entire seam.

Recommended: