Brownie is the keeper and protector of the hearth and its inhabitants. A charming talisman can be crafted from the most affordable materials at hand.
It is necessary
- - synthetic winterizer;
- - Titan glue, cardboard;
- - twine (jute);
- - nylon material (tights 20 den);
- - flax fiber (sanitary flax);
- - a case from a kinder surprise;
- - eyes (painted halves of peas);
- For the hat:
- - cell from the lattice from under the eggs (rough);
- - colored linen cord;
- - a piece of green cloth;
- - 2 sunflower seeds;
- - green felt-tip pen;
- - paint (red, white, golden aerosol);
- For shoes:
- - burlap, Titanium;
- - jute twine;
- - foamed polyethylene;
Instructions
Step 1
To make the nose, cut off the desired size of the segment folded in two layers from the tights. Make a small round lump of padding polyester. Place a pad of padding polyester under the pantyhose material just above the center point of the cut. Then, grabbing the lump with a cloth, pull with the thread, forming a round nose.
Step 2
The basis of the head of the pupa will be a case from a kinder surprise, which must be covered with nylon. Since it is rather difficult to cover the case with knitted fabric, due to the sliding of the material on the plastic base, it is necessary to apply a small drop of glue to the case. Then proceed to covering the base with a cloth, placing a nylon blank with a "nose" on the case so that the "nose" is located in the middle or slightly below the middle of the future doll's head. Pull the edges of the fabric at the crown of the head, securing with thread. Cut off excess fabric.
Step 3
To prevent the spout from sticking out, fix it with a drop of glue (at the bottom of the ball) and slightly flatten the spout with your finger. Glue the finished eyes. Make a beard. Pulling a small tuft of flax fiber in the middle with the thread, pull the ends down and form an even beard. Glue on the beard, positioning it under the nose. Then trim gently to the desired length.
Step 4
Cut a small strip from the rest of the nylon material. Grasping the short sides, pull the strip so that the edges curl up to form a "string". Cut a small piece from this "string" and form a small round mouth, securing it with glue over the beard under the nose. Make a wig. Prepare two sections of the flax strand: one larger, the other smaller. Drag them in the middle with a thread and glue them to the head: glue the small segment on top, and the larger one on the back of the head.
Step 5
Make a hat. Cut out one roughened cell from the egg rack. Glue a colored linen cord on the edge of the base of the hat. Decorate the hat with berries and leaves, securing them with glue. Cut the leaves out of green fabric, draw the veins with a green felt-tip pen. Make berries from sunflower seeds painted with white and then red paint. To determine the length of the wig, try on a finished hat and make a "haircut".
Step 6
To make the little man look pretty, use dry makeup on your face. Tone the cheeks and nose. Underline the section of the eyes with a felt-tip pen and draw the eyebrows.
Step 7
Make shoes. Cut 2 rectangles out of polyethylene foam (base for shoes). Glue the burlap on top, cutting off the excess fabric to the shape of the base of the shoes. On one side, cut the corners with scissors, depicting the toe of the shoe.
Step 8
On the sole of the base of the shoe, glue an oval made of twine and gradually, with a smooth transition, glue the twine to the side of the shoe, ending with turns of twine on the heel of the shoe. Glue funny thin legs, from a piece of twine, make knots at the ends and glue them into the middle of the stacked turns of the back of the shoes.
Step 9
Cut the horseshoe out of a piece of cardboard and cover with golden spray paint. Put it all together. On a piece of twine, and these will be handles, tie knots and glue a horseshoe to them. Glue the handles and legs with shoes on the back to cover the gluing area with a wig. Attach a small loop to the hat, through which you thread the thread, as this is a pendant doll. Then glue the hat to the head.
