Knitted underwear provides as much room for imagination as sweaters or dresses. It can be dense and delicate, with a variety of decorations. You can knit underwear both crochet and knitting. The style will tell your imagination. Among other things, you can make linen for a specific dress.
It is necessary
- - cotton threads
- Iris, snowflake, poppy;
- - hook number 1, 5 or 2, depending on the thickness of the threads;
- - patterns;
- - clasp - button, hook or plastic buckle;
- - straps adjusters;
- - rubber thread;
- - a piece of jersey to match the threads.
Instructions
Step 1
Start making a set of underwear with a shirt. It is not much different from a tank top, so there should be no problems. The shirt can be knitted even without a pattern. Determine its width. To do this, you need to measure the circumference of your chest and hips. For a product with a sufficiently free form, the larger one is taken. This is usually the circumference of the hips. Only in cases where the chest is very large, the girth of the chest is taken as a basis. In this case, you do not need half measurements, as when sewing, but full ones.
Step 2
Calculate the single crochet and openwork knitting. Tie a chain of the required number of loops and close it in a circle. Knit the first few rows in a circle, making 2 air loops at the beginning of each row. Complete an openwork border. This can be, for example, a mesh on which the embroidery will go. Knit 1 double crochet into the previous row, then make an air loop and skip 1 double crochet, knit the next double crochet into the previous row. In this way, alternate the loops to the end of the row. Knit 5-6 rows with a net and go back to single crochets.
Step 3
Knit in single crochet across the armpits. You can make one row of mesh at the waist in order to insert a belt there in the future. Having knitted to the armhole, go back to the mesh and knit 5-6 rows with it. Finish the shirt with two or three rows of simple posts, and knit the last couple of rows with a rubber thread.
Step 4
Mark the places for the straps. They can be tied, for example, with braid. Cast on a chain of 6 loops, tie the first row of a column into a column, making 2 loops at the beginning of the row. Then knit 6 stitches at the beginning of each row. There should be 6 columns everywhere. Make the straps of the desired length and attach them to the designated places of the shirt. Decorate with mesh embroidery or applique. Since this is linen, the embroidery should be soft.
Step 5
For the bra and panties, you will need a pattern. It can be taken from any fashion magazine. If there is nothing suitable in the magazines, rip your panties and bra apart at the seams and circle them on graph paper or whatman paper. No seam allowances are needed, so trace around the parts themselves. You will need the pattern in the future.
Step 6
Start knitting the panties on top. Perform the first few rows with a rubber thread. You can knit and immediately from cotton yarn, and rubber tie after. The most appropriate knitting is single crochet. You must start adding loops on the sides immediately. Before the last loop and after the initial lifting chain, knit 2 columns in one. Don't forget to try on the sewing work. It is better to make panties from two parts - front and back.
Step 7
For leg cutouts, do not knit a certain number of stitches in each row. It depends on the style. For example, start a row of the front part in the usual way, knit a section of the side and middle, then turn the work over, make 2 loops on the rise and then knit only the middle part. In the first and second rows, it is necessary not to tie 15-20 loops, in the next - 2-3, depending on the pattern. The leg cutouts on the back will be slightly smaller than on the front.
Step 8
The sides of the front and back can be tied with a net, only the posts should be the same height as the main ones. You can decorate the panties with the same mesh embroidery as the shirt. Tie a rubber string around the leg openings. Cut out a rectangle from thin jersey 6-8 centimeters long and a width equal to the distance between the legs. Make a gusset out of it and sew it to the wrong side of the panties.
Step 9
Start knitting the bra from the cups. Cast on a chain of 5 stitches, close it into a ring and knit 10 stitches inside the ring. Then knit in simple columns, evenly adding loops to make a cup. The number of added columns is determined experimentally.
Step 10
Tie the straps and ties with braid, like the straps of the shirt. You can make them longer and fix them at the desired height with the adjusters. Sew a button or plastic buckle to the ties. The swimsuit bra can be left unclasped by making the braid longer on both sides.
